trim bumpers? - NCRS Discussion Boards

trim bumpers?

Collapse
X
Collapse
 
  • Page of 1
  • Time
  • Show
Clear All
new posts
Previous template Next
  • Anthony P.
    Expired
    • October 26, 2011
    • 199
    #1

    trim bumpers?

    Ok need some assistance as to the proper placement of the mid year roadster interior quarter trim panel bumpers LIC part #19-72, 3 per panel what are the correct location on the panel?

    Once again thanks in advance.
    Tags: None
      • Top
    • Anthony P.
      Expired
      • October 26, 2011
      • 199
      #2
      Re: trim bumpers?

      My thoughts also, I don't have a clue, it is obvious that mine are missing with no signs or marks on the trim panel as to thier very existance.
        • Top

        Comment

        • Wayne M.
          Expired
          • February 29, 1980
          • 6414
          #3
          Re: trim bumpers?

          I've looked at the section in the LIC catalog, and also the '65 AIM UPC 1, sheet F13, and I can't see where these are part of typical factory installation (at least for that production year).
            • Top

            Comment

            • Anthony P.
              Expired
              • October 26, 2011
              • 199
              #4
              Re: trim bumpers?

              Wayne, Thanks for the response, I have an AIM for my 66 and can't see it either, no signs/marks etc on the original panels so with what you and I see I might think it is some after market fix for rattles or squeaks. I will leave them the way they are! Thanks for the effort!

              Tony
                • Top

                Comment

                • Ray G.
                  Extremely Frequent Poster
                  • May 31, 1986
                  • 1187
                  #5
                  Re: trim bumpers?

                  Tony;
                  I don't recall these bumpers, but is it possible they are installed on the forward edge going into the inner edge of the door jam to stop the panel from rattling.
                  And when you get the choice to sit it out or dance
                  I hope you dance


                    • Top

                    Comment

                    • Richard M.
                      Super Moderator
                      • August 31, 1988
                      • 11302
                      #6
                      Re: trim bumpers?

                      Ray is onto it........

                      Those are anti-rattle bumpers that go on the edge of the quarter trims. I found a few on a 67 convertible I restored. One side needed them, the other side did not. They were fitted on the edge of the trim that then fits into the mating hollow edge of the rear door pillar jamb. If the edge of the trim rattles when installed, it helps keep it quiet. On the side that didn't have them, the trim fit in the door pillar groove tightly so no room for the rubber piece.

                      I have never seen them shown as a required part in the AIM. I suspect they added them on the line only if needed, or maybe at the dealers due to customer complaints. Maybe a TSB. 1967 AIM UPC 1 ASM F14 shows no reference to the part.

                      Qtrbumper1.jpg Qtrbumper2.jpg P4020004.jpg P3290034.jpg
                        • Top

                        Comment

                        • Anthony P.
                          Expired
                          • October 26, 2011
                          • 199
                          #7
                          Re: trim bumpers?

                          yes that makes perfect sense Thanks guy for your reserch!!
                            • Top

                            Comment

                            Previous template Next
                            Working...
                            Searching...Please wait.
                            An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

                            Please push the back button and reload the previous window.'
                            An unexpected error was returned: 'Your submission could not be processed because the token has expired.

                            Please push the back button and reload the previous window.'
                            An internal error has occurred and the module cannot be displayed.
                            There are no results that meet this criteria.
                            Search Result for "|||"