56 or 57 rear axle housing bearing retainer - NCRS Discussion Boards

56 or 57 rear axle housing bearing retainer

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • Dee R.
    Infrequent User
    • November 23, 2021
    • 6

    56 or 57 rear axle housing bearing retainer

    I have a 57 fuelie in the middle of restoration. my axles had bearing and retainer rusted on. I cut bearing and retainer off. trying to replace the proper bearing retainer. The correct bearing was sent to me, but the new bearing retainer was too shallow. can't find the deeper version. axle housing may have been built in 1956? the bearing retainer I need is 1 inch deep. So far everyone has the one that is 1/4 inch deep? anyone have a suggestion? pretty sure the axle housing was built in 56, but on a 57. Where can I get two one inch deep?
  • Jim L.
    Extremely Frequent Poster
    • September 30, 1979
    • 1808

    #2
    Re: 56 or 57 rear axle housing bearing retainer

    Your best source of info will be a fellow who goes by the screen name "DZAUTO" on Corvette Forum. Post your question there and he WILL be able to guide you.

    Comment

    • Dee R.
      Infrequent User
      • November 23, 2021
      • 6

      #3
      Re: 56 or 57 rear axle housing bearing retainer

      JIM, I sent a message to "AZAUTO" message returned no one found under AZAUTO. can you guide me on another way to make contact?

      Comment

      • Tony R.
        Very Frequent User
        • April 19, 2017
        • 201

        #4
        Re: 56 or 57 rear axle housing bearing retainer

        Dee - Your first letter is wrong. D as in dog.

        Comment

        • Gary C.
          Administrator
          • October 1, 1982
          • 17662

          #5
          Re: 56 or 57 rear axle housing bearing retainer

          Dee,

          Photos of the axle housing and its ends would be helpful.

          Gary
          ....
          NCRS Texas Chapter
          https://www.ncrstexas.org/

          https://www.facebook.com/profile.php?id=61565408483631

          Comment

          • Mark S.
            Very Frequent User
            • July 31, 1983
            • 660

            #6
            Re: 56 or 57 rear axle housing bearing retainer

            IMG_2215 (1).jpgIs this the bearing retainer you are looking for?

            Comment

            • Terry D.
              Extremely Frequent Poster
              • May 31, 1987
              • 2691

              #7
              Re: 56 or 57 rear axle housing bearing retainer

              Did you check the Corvette forum for DZAUTO?

              Comment

              • Dee R.
                Infrequent User
                • November 23, 2021
                • 6

                #8
                Re: 56 or 57 rear axle housing bearing retainer

                Jim I am still trying to figure out this website. I did send it with the first letter D not A. At this point I am not sure how to send a message in this forum. I'm still experimenting. Now I am trying to send a picture of the retainer. It usually takes me a while to catch on, but I keep trying

                Comment

                • Tony R.
                  Very Frequent User
                  • April 19, 2017
                  • 201

                  #9
                  Re: 56 or 57 rear axle housing bearing retainer

                  Just to be super clear, the Corvette Forum is a different site than this one. Not saying I prefer one over the other. I happen to go to both pretty much daily. Apparently I have too much time on my hands.

                  I don't know if DZAUTO spends time on this site or not.

                  I don't think anyone on here recommending you consult him has anything against this site or anyone on it. But having seen some of his posts on rear-ends on the other site, I would look to contact him if I were you. I had issues with my 54 rear end and he was helpful.

                  Comment

                  • Dee R.
                    Infrequent User
                    • November 23, 2021
                    • 6

                    #10
                    Re: 56 or 57 rear axle housing bearing retainer

                    I have a 57 fuelie in the middle of restoration. my axles had bearing and retainer rusted on. I cut bearing and retainer off. trying to replace the proper bearing retainer. The correct bearing was sent to me, but the new bearing retainer was too shallow. can't find the deeper version. axle housing may have been built in 1956? the bearing retainer I need is 1 inch deep. So far everyone has the one that is 1/4 inch deep? anyone have a suggestion? pretty sure the axle housing was built in 56, but on a 57. Where can I get two one inch deep

                    Comment

                    • Gary C.
                      Administrator
                      • October 1, 1982
                      • 17662

                      #11
                      Re: 56 or 57 rear axle housing bearing retainer

                      Dee,

                      Without photos of the axle housing and ends, it's hard to tell what you have. With photos you'll receive some guidance.

                      BTW, welcome to NCRS.

                      Gary
                      ....
                      NCRS Texas Chapter
                      https://www.ncrstexas.org/

                      https://www.facebook.com/profile.php?id=61565408483631

                      Comment

                      • Leif A.
                        Extremely Frequent Poster
                        • August 31, 1997
                        • 3629

                        #12
                        Re: 56 or 57 rear axle housing bearing retainer

                        Originally posted by Dee J Russell (68619)
                        Jim I am still trying to figure out this website. I did send it with the first letter D not A. At this point I am not sure how to send a message in this forum. I'm still experimenting. Now I am trying to send a picture of the retainer. It usually takes me a while to catch on, but I keep trying
                        Tom Parsons (DZAuto) is a long time member here. He last posted on a thread on February 6, 2022. You can go to the member list and find him and then send him a e-mail. Go to the home page, click on the members tab, scroll down to members list, and then click on the "T" in the header bar for "Tom". Tom Parsons is on page 21 of that list. Click on his name and send him an email...he knows the C1 inside and out.
                        Leif
                        '67 Coupe L79, M21, C60, N14, N40, J50, A31, U69, A01, QB1
                        Top Flight 2017 Lone Star Regional

                        Comment

                        • Tom P.
                          Extremely Frequent Poster
                          • April 1, 1980
                          • 1814

                          #13
                          Re: 56 or 57 rear axle housing bearing retainer

                          I do come here some, but I also spend more time on the CORVETTE FORUM. Even though I've been an NCRS member since 1980, I just never fit the NCRS mold.
                          I have a new home email address twparsons6@gmail.com
                          By the way, I FULLY UNDERSTAND his dilemma and can thoroughly explain----------------with pictures, if he so chooses.
                          AND, from what he has explained so far, WITHOUT QUESTION, he has a 1956 axle housing under his 57. I'm positive that everyone here knows for a fact that there was NO SUCH THING as a 56 style axle housing installed under a 57 at the St. Louis assembly plant. NOPE, did not happen!

                          Comment

                          Working...
                          Searching...Please wait.
                          An unexpected error was returned: 'Your submission could not be processed because you have logged in since the previous page was loaded.

                          Please push the back button and reload the previous window.'
                          An unexpected error was returned: 'Your submission could not be processed because the token has expired.

                          Please push the back button and reload the previous window.'
                          An internal error has occurred and the module cannot be displayed.
                          There are no results that meet this criteria.
                          Search Result for "|||"